 |
|||
|
|
|||
|
|
|
Epoxy.com Product #10 100% Solids Lo-Mod Low Viscosity Adhesive/Binder GENERA L DESCRIPTIONEpoxy.com Product #10 is a 100% solids Lo-Mod Low Viscosity adhesive
used as a binder for epoxy mortar systems in patching and grouting applications, as a seal
coat for non-skid surfaces outside, and as a primer to insure high bond strength for
coatings and patches. ADVANTAGES
SURFACE PREPARATION Surface must he clean and sound. Remove all dirt, laitance,
grease curing compounds and other foreign matter by sandblasting, mechanical abrasion, or
acid etching. Remove water and dust from all surfaces with an oil-free blast immediately
prior to application. MIXING INSTRUCTIONS Temperature of Product #10 must be 50 degrees F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part 8 for three minutes with a low speed electric drill motor equipped with a mixing paddle. To prepare a mortar, slowly add 3-5 parts by volume of clean,
dry, well graded sand to one part by volume of mixed epoxy. Continue to mix until
aggregate is thoroughly wetted down. APPLICATION Epoxy.com Product #10 can be applied with a brush, roller or squeegee when
used as a primer or seal coat. For skid resistance, broadcast sand at a rate of 2 lbs. per
square yard. For mortar applications finish surface with trowel. Prime surface to be
patched with neat material. LIMITATIONS Use of solvents for thinning will prevent proper cure. New
concrete must he 28 days old prior to application of Product C10. Temperature of substrate
must be above 40 degrees F. SAFETY PRECAUTIONS Prolonged or repeated exposure may cause eye and skin irritation.
If contact occurs, wash immediately and seek medical help. Use safety glasses with side
shields and wear protective rubber gloves. CLEANING INSTRUCTIONS All tools and equipment should be cleaned before the system gels.
Use MEK, Acetone, or any lacquer solvent.
| ||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
Click
the picture
