Epoxy.com Product #1700Electrical Encapsulating & Casting EpoxyDESCRIPTIONProduct #1700 Electrical Encapsulating & Casting Epoxy is a two component 100% Solid epoxy compound used as an electrical encapsulation material where ease of use and high electrical resistivity are needed. Product #1700 Electrical Encapsulating & Casting Epoxy is a low viscosity, low odor material with a pourable viscosity. Electrical Encapsulating & Casting Epoxy has a convenient 1 to 1 by volume mix ratio and a long pot life. Product #1700 Electrical Encapsulating & Casting Epoxy has a very low exotherm on curing allowing for large parts with extremely low shrinkage. WHERE TO USE
PROPERTIES
SURFACE PREPARATIONProper preparation of the substrate is essential for good bond. Substrate must be both clean and sound. Remove laitance, oils, and greases by solvent wiping. When bonding steel based plates sandblast the bottom of base plate and wipe clean with an approved metal-cleaning solvent, where necessary. MIXINGFor ease of handling, condition Product #1700 Electrical Encapsulating & Casting Epoxy to a minimum temperature of 70°F before mixing. Mix Ratio 100 parts A Component to 125 parts B component by weight (1 to 1 by volume). Mix components together well for 2 to 3 minutes in a non absorbent container large enough to allow decent mixing. Scrape sides and bottom to ensure through mixing. Avoid entrapping air , let set for 10 minutes to release air then pour in place. Automatic dispensing equipment may be utilized. APPLICATIONProduct #1700 Electrical Encapsulating & Casting Epoxy may be cast in single or multiple lifts, up to 4 inches thick. If multiple pours are done material must be placed within 72 hours. Clean equipment with MEK, xylene, Acetone other approved solvent. PACKAGING:Product #1700 Electrical Encapsulating & Casting Epoxy is conveniently packaged in 1 gallon or five gallon containers. COVERAGE:231 cubic inches per gallon. At 1/8 inch thick 12.8 SF Per gallon. Use the calculator below to double check your estimate. CAUTION: Product #1700 Electrical Encapsulating & Casting Epoxy contains epoxy resins and organic amines. May cause skin sensitization or other allergic responses. Avoid inhalation of vapor. Use with good ventilation. Prevent contact with skin and eyes. If eyes are contacted, flush immediately with water and contact a physician. Skin contact wash thoroughly with soap and water.
| ||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2010 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]
|
