|
|
|||
|
|
| ||||||||||||||||||||||||||||
| HANDLING PROPERTIES | |
| Mix Ratio | 3.5 to 1 by Volume |
| Color | straw |
| Mixed Viscosity (@77 Degrees F) | 275-350 CPS |
| Gel Time | 12 - 15 Minutes |
| Shelf Life: (@85 Degrees F Maximum Temp) | 1 Year |
| Initial Cure | 24 hours |
| Final Cure | 7 days |
| PHYSICAL PROPERTIES | |
| Elongation (ASTM D-638) | 1.6% |
| Tensile Strength (ASTM D-638) | 6,970 p.s.i (Min.) |
| Modulus of Elasticity (ASTM D-638) | 444,800 |
| Compressive Strength (ASTM C109-75) | 12,220 |
| Bond Strength, 7 days @ 77°F (AASHTO T237-73) | 7,380 |
SURFACE PREPARATION: Drilling of cracks for injection ports is best accomplished with a vacuum attached to a swivel drill chuck and hollow core drill bits. The surface of the crack and the area around the injection ports should be sealed with Epoxy.comTM Product #5, 6 or 48. Entry ports for injecting should be spaced at appropriate intervals to accomplish the full penetration of the resin. As with all injection resins, use of a plural component epoxy injection machine is the only way to insure desired results.
MIXING PROCEDURES: Supplied as two-package system. Pour Component "B" into the injection machine container labeled "B". Pour the Component "A" into the injection machine container labeled "A". Use special caution not to intermix components, or with different injection resins.
APPLICATION STEPS: ESITM Product #3 should only be pumped with a positive displacement injection machine. See technical data on Concrete Injection Procedures.
HANDLING PRECAUTIONS
Prolonged or repeated exposure may cause eye and skin irritation. Avoid contact with skin or eyes. If contact occurs, wash immediately with soap and water. Flush eyes immediately with water and contact physician. If used indoors, provide adequate ventilation. Use safety glasses, and wear protective rubber or polyethylene gloves.
For more information on injection procedures , injection accessory products or other Epoxy.com Products, please contact:
Epoxy Systems, Inc.
This information is presented in good faith to assist the user in
determining whether our products are suitable for his application. All statements,
technical information and recommendations contained herein are based on tests we believe
to be reliable, but the accuracy or completeness thereof is not guaranteed, and the
following is made in lieu of all warranties, expressed or implied: Seller's and
manufacturer's only obligation shall be to replace such quantity of the product proved to
be defective. Neither seller nor manufacturer shall be liable for any injury, loss or
damage, direct or consequential, arising out of the use of or the inability to use the
product. Before using owner shall determine the suitability of the product for his
intended use, and Owner assumes all risk and liability whatsoever in connection therewith.
No statements or recommendations not contained herein shall have any force or effect
unless in an agreement signed by the officers of seller and manufacturer. All of the
information on this product contained in this bulletin is to be used as a guide and is
subject to change without notice. No warranty or representation however, is intended
or made, nor is protection from inferred, and all patent rights are reserved. This
bulletin supersedes all previous specifications. 930201.1230.010
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
|
