Epoxy.com Product #406
Two Component Low
VOC Chemical Resistant Polyurethane Coating
DESCRIPTION
Epoxy.com Product #406 is a two component, chemical resistant,
polyurethane coating.
Epoxy.com Product #406
is a low VOC compliant urethane that meets all federal and state
environmental air quality standards. The high gloss finish offers excellent
abrasion resistance, chemical and stain resistance, and superior color
retention.Epoxy.com Product #406 can be used equally well on vertical
or horizontal surfaces. It is ideal for concrete floors and walls in
warehouses, storage facilities, aircraft hangars, animal housing, and
vehicle maintenance facilities. Available in both clear and pigmented
formulations,
Product#406
can be used as a finish coating option for most Epoxy.com Flooring Systems.
ADVANTAGES
-
Excellent Abrasion Resistance
-
Excellent Chemical & Stain Resistance
-
Suitable for Both Exterior & Interior Applications
-
May be Used for Both Horizontal & Vertical
-
Compliant to Low VOC Air Regulations
CONSIDERATIONS
- Substrate temperature must be a minimum of 50ºF
- Substrate must be free of dirt, waxes, curing agents, and other
foreign materials
- Minimum Application Temperature: 40ºF (contact Epoxy.com for Low
Temperature Cure)
- Maximum Application Temperature: 100ºF
COMPOSITION
Two component, catalyzed, chemical resistant polyurethane.
APPLICATION
SURFACE PREPARATION
Surface Preparation is the most critical portion of any
successful resinous flooring system application. All substrates must be
properly prepared as outlined in Epoxy.com Surface Preparation Procedures.
Work must be performed by trained or experienced contractors or maintenance
personnel.
INSTALLATION
Epoxy.com Product #406 is normally applied with a brush,
short napped roller, or squeegee and back-rolled with a short nap roller.
Care should be taken to minimize the entrapment of air caused by
over-rolling.
Epoxy.com Product #406 can also be applied by airless or
conventional spray. May be thinned 9-10% with Ethyl Ethoxy Propanate (EEP)
or Methy Amyl Ketone (MAK).
CLEAN UP
Clean skin with soap and water. Tools and equipment should
be cleaned with xylene or lacquer thinner.
COVERAGE
Epoxy.com Product #406 Clear will yield approximately 2.9 mils dry film
thickness when spread at 300 ft2 per gallon.
Epoxy.com Product #406 Pigmented will yield approximately 3.5 mils dry
film thickness when spread at 300 ft2 per gallon.
COLOR SELECTION
Epoxy.com Product #406 is available in Clear (gloss or
satin) and 17 colors. Custom Colors are available subject to laboratory
approval, minimum quantity, lead time for production, and increased cost.
TECHNICAL DATA
| Viscosity @ 75ºF |
125-150 cps, mixed, Clear |
|
Mixing Ratio |
3 Parts A to 1 Part B by Volume |
| Solids Content (by Volume) |
54.26% Clear
66.46% Pigmented |
| Volatile Organic Content (VOC) |
1.56#/gal (187 gm/L) Clear
1.39#/gal (166 gm/L) Pigmented |
| Weight per Gallon |
9.85 pounds per gallon , mixed, clear |
CURE/DRY TIME
| Pot Life |
8 hours @ 75ºF |
| Dry to Touch |
10-14 hours @ 75º |
|
Re-Coat |
12-16 hours @ 75º |
| Light Service |
16 hours @ 75º |
| Full Cure & Maximum Resistance |
5-10 days |
AVAILABILITY
Contact Epoxy.com
MAINTENANCE
After completing the application of Epoxy.com Product #406, the installer
should provide the owner with maintenance instructions.
Epoxy.com Product #406 is easily cleaned with neutral soaps or
detergents.
TECHNICAL SERVICE
Epoxy.com Technical Support provide services and consultations on
material selection, specification, troubleshooting, and other information on
the proper repair and protection of concrete surfaces.
CHEMICAL RESISTANCE
REAGENT RATING
- Acetic Acid-5% L
- Acetone L
- Betadine R
- Beer R
- Bleach L
- Brake Fluid R
- Citric Acid-30% R
- Citric Acid-40% L
- Crude Oil R
- Diesel Fuel R
- Ethylene Glycol R
- Fatty Acids L
- Gasoline R
- Hydrochloric Acid-15% R
- Iodine R
- Lactic Acid-15% R
- Methyl Ethyl Ketone L
- Nitric Acid-10% R
- Orange Juice R
- Peroxide-35% R
- Phosphoric Acid-85% L
- Skydrol R
- Sodium Hydroxide-50% R
- Sulfuric Acid-20% R
- Toluene R
- Urea R
- Vinegar L
- Xylene R
R-Recommended for continuous service.
L-Limited Recommendation, occasional spills.
*-May cause slight stain or discoloration.
|
|
Proper mixing and installation is critical to the optimal success
of all product. See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
350 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers. |
Copyright © 1994-2010 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four
(4) months; Power Tools and Equipment 90 days; Vinyl Esters,
High Molecular Weight Methacrylates (HMMA) and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
|