Epoxy.com Product # 5
100% SOLIDS HI-MOD FAST SETTING GEL ADHESIVE
DESCRIPTION
Epoxy.com Product #5 Hi Mod Fast Setting Gel Adhesive is a 100% solids
high-mod epoxy gel adhesive used for vertical and overhead bonding
applications and structural repairs. It is also used as a grout for
anchor bolts, dowels and rebar.
ADVANTAGES
- Moisture insensitive (cures on damp or wet surfaces)
- Non-sagging (ideal for setting injection ports)
- Proven field performance
- Strong yet resilient
- Quick Setting
- High Early Strength
APPLICATION PROCEDURES
Surface Preparation:
Before application of Epoxy.com Product #5 Hi Mod Fast Setting Gel
Adhesive, surface to be bonded must be clean and sound. Remove all
dirt, laitance, grease, curing compounds and other foreign mater by
sandblasting, or mechanical abrasion. Remove water and dust from all
surfaces with an oil-free air blast immediately prior to
application.
Mixing Instructions:
Temperature of Epoxy.com Product #5 Hi Mod Fast Setting Gel
Adhesive must be 50 F. or above at time of mixing. Stir each
component separately before blending thoroughly. Mix one part by
volume of component A with one part by volume of component B for
three minutes with a low speed electrical drill motor equipped with
a mixing paddle. Pot life is approximately 10 to 15 minutes at 72 F.
Gel time varies depending on the ambient temperature. Consult
Epoxy.com Tech Service for specific information.
To prepare a mortar for structural repairs add one part by volume of
dry, clean, well-graded select sand to one part by volume of mixed
epoxy.
Application:
Apply Epoxy.com Product #5 Hi Mod Fast Setting Gel Adhesive with a
spatula, trowel, concrete grout bag or caulking gun. Limitations
Temperature of substrate must be above 40 F. Alteration of Epoxy.com
Product #5 Hi Mod Fast Setting Gel Adhesive with solvents for
thinning purposes will prevent proper cure.
SAFETY PRECAUTIONS
Prolonged or repeated exposure may cause eye or skin irritation. If
contact occurs, wash immediately and seek medical help. Use safety
glasses with side shields and wear protective rubber or polyethylene
gloves.
CLEANING
All tools and equipment should be cleaned before the system gels. Use
toluene, methyl ethyl ketone or any lacquer solvent.
SPECIFICATIONS
Epoxy.com Product #5 Hi Mod Fast Setting Gel Adhesive meets
ASTM C-881-90 Type I, II, IV, & V when used at
temperatures of 40 F. and below.
APPLICATION PROPERTIES @ 77° F.
|
|
Mix Ratio |
1:1 by Volume
|
|
Consistency |
Paste with 1/2" hang
|
|
Gel Time (200 gr.) |
10-15 minutes
|
|
Initial Cure |
30 minutes
|
|
Final Cure |
24 hours |
|
Packaging |
1 gal. cans, 5 gal. pails, drums
|
PHYSICAL PROPERTIES
|
|
Tensile Strength (ASTM-638) |
4,200 p.s.i min |
|
Tensile Elongation (ASTM D-638) |
4% max.
|
|
Shore D Hardness (ASTM D-2240) |
80 +/- 5
|
|
Compressive Strength (ASTM D-695) |
11,000 p.s.i min.
|
|
Flexural Strength (ASTM D-790) |
8600 p.s.i
|
Coverage:
There are 231 cubic inches to a gallon. So you will get about 25.6
square feet per of 1/16 inch thickness. If using this as an anchor
bolt, or dowel bar adhesive, you can double check you volume with the
Epoxy.com Dowel Bar and Anchor Bolt Adhesive Calculator.
|
|
Proper mixing and installation is critical to the optimal success
of all product. See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
350 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers. |
Copyright © 1994-2010 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four
(4) months; Power Tools and Equipment 90 days; Vinyl Esters,
High Molecular Weight Methacrylates (HMMA) and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
|