Epoxy.com Product #629
Chemical Resistant Novolac Conductive Flooring
DESCRIPTION
Epoxy.com Product #629 Chemical Resistant Conductive Flooring
is a 100% solids epoxy Novolac Conductive coating ideal for severe chemical
and solvent storage requiring conductive and spark proof surfaces. Applied
at a nominal 1/16 inch, the Conductive Novolac offers the superior chemical
resistance of a Novolac Resin System while maintaining a conductive surface.
- Low viscosity ideal for trowel application
- Exhibits excellent resistance to strong acids, alkalis and most
industrial chemicals and solvents
- 100% Solids low odor application and cure (0-VOC)
- Bonds well to cool, damp substrates
- Conductive & non sparking, 25,000 to 1,000,000 ohms resistivity
CONSIDERATIONS
- Substrate temperature must be a minimum of 50oF
- Substrate must be free of dirt, waxes, curing agents and other foreign
materials
- Steel surfaces must e free of grease and oils.
Abrasive blast to SSPC-SP-3
COMPOSITION
100% Solids, modified polyamine, cured epoxy Novolac resin and fillers
APPLICATION
SURFACE PREPARATION
Surface Preparation is the most critical portion of any
successful resinous flooring system application. All substrates must
be properly prepared as outlined in
Epoxy.com Surface Preparation
Guide.
INSTALLATION
Installation of Epoxy.com Product #629 NOVOLAC CONDUCTIVE
will vary with application. Normally spread with a trowel or
squeegee and back-rolled with a medium or short nap roller.Care
should be taken to minimize the entrapment of air caused by over
rolling.
For complete instructions, consult installation guide or
Epoxy.com Technical Support.
CLEAN-UP
Clean skin with soap and water. Tools and equipment should be
cleaned with xylene or lacquer thinner.
Product #629 NOVOLAC CONDUCTIVE will yield
approximately 32 mils when spread at 50 ft
2 per gallon. Two coats required.
COLOR
Epoxy.com Product #629 CONDUCTIVE is available in
Epoxy.com
Standard Colors and Custom Colors as approved.
 Click
the picture of color card below for a larger version of this picture
of the color chart.
Please
note: The picture to the right is a photographic reproduction of the
color card for this product. The photo reproduction process and your
monitor and/or printer will change these colors. This chart is to give you
an idea of the colors available and not intended for critical color selections.
TECHNICAL DATA
| Viscosity @ 75oF |
1,000-1,500 cps |
| Mixing Ratio by volume |
2 Part A to 1 Part B by Volume |
| Solids Content by volume |
100 by volume |
| Volatile Organic Content |
0 |
| Weight per gallon, mixed |
11.0-11.5 lbs. per gallon mixed |
CURE/DRY TIME
| Pot Life |
20-25 min. @75 Degrees F |
| Dry to Touch |
6-7 hours @ 75 Degrees F |
| Re-Coat |
8-12 hours @ 7 5Degrees F |
| Light Service |
24 hours @ 75 Degrees F |
| Full Cure & Maximum Resistance |
5 days |
CHEMICAL RESISTANCE
| REAGENT |
RATING |
| Acetic Acid-10%, 30% |
R |
| Acetone |
L |
| Ammonia Hydroxide-38 % |
R |
| Beer |
R |
| Bleach |
L |
| Brake Fluid |
R |
| Citric Acid-30% |
R |
| Citric Acid-40% |
R |
| Crude Oil |
R |
| Diesel Fuel |
R |
| Ethylene Glycol |
R |
| Fatty Acids |
R |
| Gasoline |
R |
| Hydrochloric Acid-37% |
R |
| Lactic Acid-50 |
R |
| Lactic Acid-80% |
R |
| Methyl Ethyl Ketone |
R |
| Methylene Chloride |
L |
| Nitric Acid-10% |
R |
| Peroxide-35% |
R |
| Phosphoric Acid |
R |
| Skydrol |
R |
| Sodium Hydroxide-50% |
R |
| Sulfuric Acid-98% |
R |
| Toluene |
R |
| Urea |
R |
| Vinegar |
R |
| Xylene |
R |
R-Recommended for continuous service
L-Limited Recommendation, occasional spills
*-May cause slight stain or discoloration
MAINTENANCE
See Epoxy.com Care and Maintenance of Seamless Flooring.
Epoxy.com Product #629 NOVOLAC CONDUCTIVE is easily cleaned with neutral soaps or detergents.
|
|
Proper mixing and installation is critical to the optimal success
of all product. See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
350 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers. |
Copyright © 1994-2010 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four
(4) months; Power Tools and Equipment 90 days; Vinyl Esters,
High Molecular Weight Methacrylates (HMMA) and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
|