Epoxy.com Product #640100% Solids Chemical and Heat Resistant CoatingDESCRIPTIONChemical & Heat Resistant Coating is a two component; highly cross linked Novolac, that is 100% solids. It can be brush, roll or airless spray applied coating designed to provide cavitation, corrosion and erosion resistance to concrete, metallic and nonmetallic surfaces. Epoxy.com PRODUCT #640 acts as an inert barrier against extremely harsh environmental factors such as low and high PH, temperature extremes, dry and fluid particulate flow and corrosive chemical attack. Link to related and similar products. USES
PHYSICAL PROPERTIES
CURED PROPERTIES
CHEMICAL RESISTANT PROPERTIESThe following represents percent flexural strength retained after two weeks cure at 770F followed by 30 days immersion in the chemical environment as described.
The following standards may be used in assessing what activities can be carried out after an application of PRODUCT #640.
Force cures may be used to either enhance chemical resistance or to allow the coating to be placed in service before 5 days. Allow a post cure of 12 to 24 hours before force curing. RECOMMENDED FORCE CURE SCHEDULE
NOTE: This product will cure well at temperatures as low as 40 - 450F. However, additional curing time must be provided. SURFACE PREPARATIONCONCRETE: Surface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, mechanical abrasion. If acid etching is used follow with abrasive or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast, or vacuum, immediately prior to application. STEEL: Prior to sand blasting remove all grease, dirt and other contaminants from the surface. Grind sharp edges to a minimum radius of 1/8 inch. Remove all weld splatters. Sandblast to a white metal finish according to SSPC-SP-5-63 or NACE standard TM-01-70 with a minimum anchor profile of 3 mils. MIXINGMix ratio is two parts by volume base ("A") to one part by volume hardener ("B"). APPLICATIONPRODUCT #640 can be applied by brush, roller or airless spray equipment. PRODUCT #640 is designed to be spray applied at 10 to 15 mils per coat. Relative humidity during the coating process should be a maximum of 90% for application to commence. A minimum of two coats is recommended. If the second coat is applied before the first coat cures, no surface preparation is required. Simply apply the second coat maintaining the required mils per coat. However, if the first coat has cured more than 24 hours, the first coat must be brush blasted prior to the second coat. CLEANINGClean all equipment immediately after use with MEK or acetone. CAUTIONWARNING! A Component contains epoxy resin. DANGER! B Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling. FIRST AID: In case of skin contact, immediately wash with soap and water. In case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing and shoes. If irritation persists, seek medical attention. Wash clothing before reuse. FOR INDUSTRIAL USE ONLY KEEP AWAY FROM CHILDREN Other customers who visited this page also visited:
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2010 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]
|
